Kitchen Knife Types

Can you sharpen a serrated knife with a regular knife sharpener?

Usually not well. Find out why standard sharpeners miss serrations, which tools do work, and how to sharpen a serrated bread knife step by step.

On this page
  1. Short Answer
  2. Why Regular Sharpeners Struggle With Serrations
  3. Sharpeners That Can Work
  4. How to Sharpen a Serrated Knife With a Tapered Rod
  5. Does Your Serrated Knife Actually Need Sharpening?
  6. When to Use a Professional or Replace the Knife
  7. FAQ

Short Answer

Generally, no, not properly. Most regular knife sharpeners are designed for a straight, continuous edge. On a serrated knife they touch mainly the points of the teeth and miss the curved hollows (gullets) between them, which is where much of the cutting happens. Some can also round off or chip the teeth.

You can sharpen a serrated knife at home, but it usually takes a different tool: a tapered sharpening rod that fits into each serration, or a sharpener with a slot made specifically for serrated blades. You can also send it to a professional sharpener.

Why Regular Sharpeners Struggle With Serrations

There are three main problems:

  • They can’t reach the gullets. A flat whetstone, a straight honing rod or the V-shaped slot of a pull-through sharpener rides along the tops of the teeth. The scalloped edges in between, which are recessed and do much of the work, barely get touched.
  • They can damage the teeth. Dragging a serrated blade through a coarse pull-through or electric slot can flatten, round or chip the points, which makes the knife cut worse.
  • They grind the wrong side. Most serrated kitchen knives are sharpened on one side only. The serrations are ground into one face, while the other face is flat. Standard two-sided sharpeners grind both sides, which adds a bevel where there shouldn’t be one.

That doesn’t mean a regular sharpener will ruin every serrated knife on the first pass, but it won’t restore the edge properly and can do gradual damage.

Sharpeners That Can Work

  • Tapered rods (ceramic or diamond). A thin, cone-shaped rod lets you match the diameter to each serration. This is the most common home method and works on most bread knives, steak knives and serrated pocket knives. Some come as part of a pocket sharpener or a guided sharpening kit.
  • Pull-through or electric sharpeners with a serrated slot. Some models include a stage marketed for serrated knives. These are quick, but results vary, and many still mainly hone the tips. Follow the manufacturer’s instructions and use only the slot meant for serrated blades.
  • Professional sharpening. Many sharpening services handle serrated knives with specialized equipment. For a good-quality bread knife, this is often the simplest option.

How to Sharpen a Serrated Knife With a Tapered Rod

Work slowly, keep your fingers well away from the edge, and rest the knife on a stable surface if that helps.

  1. Find the beveled side. Look closely at the edge. One side has the ground scallops (the bevel); the other is usually flat. You sharpen the beveled side only.
  2. Match the rod to the serration. Place the rod in a gullet. Use the part of the taper whose diameter is about the same as the serration’s curve. Too thick and it won’t sit in the scallop; too thin and it will gouge the middle.
  3. Match the angle. Hold the rod at the same angle as the existing bevel. Most serrated kitchen knives are fairly steep, often in the low 20s of degrees, but the aim is to follow the bevel that’s already there rather than hit a precise number.
  4. Stroke outward. Draw the rod through the gullet, moving away from the spine toward the edge, with light pressure. A few strokes per serration are usually enough.
  5. Check for a burr. Run a fingertip carefully across (never along) the flat side behind the serration you just worked. A slight rough lip (a burr) means you’ve sharpened through to the edge. Move on to the next serration.
  6. Repeat for every serration. This is the slow part. On a long bread knife it can take a while.
  7. Remove the burr. Lay the flat side of the blade flat on a fine stone, a ceramic rod held flat, or a strop, and make one or two very light passes to knock off the burr. Don’t tilt the blade, or you’ll create a bevel on the flat side.
  8. Test it. Slice a tomato or a piece of crusty bread. It should bite easily without much downward pressure.

Does Your Serrated Knife Actually Need Sharpening?

Serrated knives keep cutting for a long time because the recessed edges in the gullets don’t touch the board much. Signs it needs attention:

  • It slides on tomato skin instead of biting in.
  • You need noticeably more downward pressure on crusty bread.
  • It tears soft bread or leaves lots of crumbs where it used to cut cleanly.
  • You can see flattened or chipped teeth.

If the teeth are still intact and it just feels slightly off, a few light passes of a ceramic rod on the flat side (held flat) can sometimes freshen it up before a full sharpening.

When to Use a Professional or Replace the Knife

  • Micro-serrated knives (very fine teeth, common on cheap steak knives and knives sold as “never needs sharpening”) are hard or impossible to sharpen effectively at home. Replacement is usually more practical.
  • Inexpensive bread knives may cost less to replace than to have sharpened.
  • Good-quality bread knives and serrated slicers are worth sharpening, either yourself with a tapered rod or through a professional service.
  • Electric knife blades are generally meant to be replaced rather than sharpened. Check the manufacturer’s guidance. We cover electric knives in electric knives: best fillet and carving models.

If you’re still deciding whether you need a serrated knife at all, see do serrated knives cut better? And for where a bread knife fits into a basic kit, see our guide to kitchen knife types.

FAQ

Can I use a honing rod on a serrated knife?

A standard steel honing rod mainly touches the tips of the teeth, so it does little for the gullets. A thin ceramic rod can be used carefully, one serration at a time, or held flat against the flat side to remove a burr.

Can I sharpen a serrated knife on a whetstone?

Not in the normal way. A flat stone can’t reach into the serrations. You can use the edge of a stone on some knives with large scallops, or lay the flat side on a fine stone to deburr, but a tapered rod is easier and more reliable.

Will an electric sharpener ruin a serrated knife?

A standard electric slot can wear down or damage the teeth over time. Only use an electric sharpener on a serrated knife if it has a slot that the manufacturer specifically says is for serrated blades.

How often should a serrated knife be sharpened?

Much less often than a straight-edged knife. With normal home use, many bread knives go a long time between sharpenings. Sharpen when it starts slipping or crushing instead of biting.

The complete guide to kitchen knife types

Types of Kitchen Knives and Their Uses
Read the guide

Keep exploring

Guides from other topics

All topics →