Knife Sharpening

How to Raise, Feel and Remove a Burr When Sharpening

What a burr is, how to raise it along the whole edge, how to feel for it safely, and how to remove it with alternating strokes, stropping and other methods.

On this page
  1. What a burr is
  2. Why the burr matters
  3. How to raise a burr
  4. How to feel for a burr safely
  5. Why a burr won’t form
  6. How to remove the burr
  7. Stubborn burrs and wire edges
  8. How to tell the burr is gone
  9. Common mistakes

What a burr is

A burr is a thin, flexible lip of steel that forms on the edge as you sharpen. When you grind one side of the edge, the two bevels eventually meet. The very edge becomes so thin that, instead of being ground away, it bends over to the opposite side. That bent-over lip is the burr.

A light, fine burr is normal and expected. A long, floppy burr that folds back and forth is often called a wire edge. It usually comes from heavy pressure or too much work on one side.

Why the burr matters

The burr does two jobs:

  1. It proves you’ve reached the edge. If a burr runs from heel to tip, the bevel you’re grinding has met the opposite side along the whole length. If there’s no burr in a section, that section hasn’t been sharpened all the way to the apex yet.
  2. It has to go. A burr left on the knife makes the edge feel dull or “grabby”, and it breaks off or folds over in the first few cuts, leaving a ragged edge behind. Many “I sharpened it but it’s still dull” problems come down to a burr that was never removed.

How to raise a burr

  1. Choose the right stone. On a dull knife, a medium stone around 1000 grit, or a coarse stone if the knife is very dull or chipped, raises a burr far faster than a fine stone. See our guide to whetstones and grit.
  2. Hold a consistent angle. Match the existing bevel using the marker test from our sharpening angle guide.
  3. Work one side only until the burr forms. Use moderate, even pressure and work in sections (heel, middle, tip) so each part of the edge gets attention.
  4. Check often. Stop every so often and feel the opposite side of the edge.
  5. Keep going until the burr runs the full length, including the tip and right down to the heel.
  6. Then switch sides and repeat until the burr flips back over.

Our step-by-step whetstone guide shows where this fits in the whole sharpening process.

How to feel for a burr safely

Feel on the side opposite the one you’ve just sharpened. That’s the side the burr is pushed toward.

  • Place the pad of your thumb or fingertip flat on the blade face, a little way back from the edge.
  • Draw it gently across the edge, from the spine side toward the edge and off it. Never move your finger along the length of the edge.
  • With a burr, you’ll feel a slight catch, roughness or “lip” right at the edge. Without one, your finger slides off smoothly.
  • Repeat at the heel, middle and tip.

On a coarse stone the burr is easy to feel. On fine stones (roughly 3000 and above) it can become too small to detect reliably. At that stage, many sharpeners switch to matching stroke counts on each side.

Other ways to find it

  • Fingernail: rest a fingernail on the blade face and slide it gently off the edge. A burr catches the nail.
  • Light: look straight down at the edge under a bright light. A burr or a dull section shows as a bright, glinting line.
  • Magnification: a cheap loupe or phone camera zoom makes burrs easy to see.

Why a burr won’t form

Cause What’s happening Fix
Angle lower than the existing bevel You’re grinding the shoulder of the bevel, not the edge Re-do the marker test; raise the angle slightly
Not enough work yet Very dull knives take a while to reach the apex Keep going, or switch to a coarser stone
Stone too fine Fine stones remove little steel Drop to around 1000 grit, or coarser
Inconsistent angle Rocking rounds the edge instead of meeting it Slow down, lock your wrists, work in sections
Missed sections Tip or heel not touching the stone Lift the handle at the curve; start strokes right at the heel

How to remove the burr

Removing the burr is mostly about reducing pressure and alternating sides so the burr gets smaller and thinner until it falls away. Pulling it off with your fingers, or leaving it to break off in use, leaves a ragged edge.

Alternating strokes with falling pressure

Once you’ve raised a burr on both sides, alternate sides more and more often: several strokes per side, then a few, then single alternating strokes. Reduce pressure each time until you’re using little more than the knife’s own weight. This shrinks the burr from one side to the other until it’s very small.

Edge-leading finishing strokes

Finish with a few very light edge-leading strokes on each side, pushing the edge into the stone as if slicing a thin layer off it. This tends to cut the remaining burr off rather than just folding it over. Use very light pressure, especially on soft water stones.

A few strokes at a slightly higher angle

If the burr keeps flipping back and forth, raise the angle by a few degrees and make one or two very light strokes per side. This hits the apex directly and removes the last bit of burr. It also leaves a tiny micro-bevel, which makes the edge slightly more durable.

Stropping

A strop, bare leather or leather with fine compound, cleans up what’s left. Always pull the knife spine-first, with the edge trailing, using light pressure. Keep the knife at your sharpening angle or very slightly lower, so the strop works the very edge without rounding it. Alternate sides with a handful of strokes each. Our guide to strops for Japanese knives covers strop choice and technique in detail. If you don’t have a strop, newspaper or cardboard laid on a flat surface works in a pinch.

Drawing through wood, cork or felt

For a burr that won’t let go, gently draw the edge through the end of a cork, a piece of soft wood, or a felt pad, as if making a very light cut. This snags and tears off the weakened burr. Afterward, make a few light alternating strokes on your finest stone or strop to clean up the apex.

Stubborn burrs and wire edges

  • Stainless steels often form tougher, more persistent burrs than carbon steels. Expect to spend more time deburring them.
  • Wire edges usually come from too much pressure or too many strokes on one side. Lighten up, alternate sooner, and if needed, cut the wire edge off with the wood or cork method. Then lightly re-sharpen with alternating strokes on a fine stone.
  • Pull-through sharpeners often leave a burr that’s hard to remove inside the slot, which is one reason their edges dull quickly. See are pull-through sharpeners bad for your knives.

How to tell the burr is gone

  • No catch when you feel across the edge on either side, at the heel, middle and tip.
  • No bright line when you look down at the edge under a light.
  • Paper slices cleanly, with no snagging and no change in feel from heel to tip.
  • The edge cuts the same on the first few slices as it did straight off the stone. If it suddenly gets worse, a burr probably broke off.

Common mistakes

  • Moving on before the burr runs the full length, usually missing the tip or heel
  • Pressing hard while deburring. Heavy pressure creates a new burr instead of removing the old one.
  • Stropping at too high an angle, which rounds the edge
  • Feeling the edge along its length instead of across it
  • Skipping deburring entirely and blaming the angle. A clean 20° edge can feel sharper than a 15° edge with a burr still attached, as we explain in is 15 or 20 sharper for a knife.

The complete guide to knife sharpening

Best Knife Sharpening Angle: 15 vs 20 Degrees
Read the guide

Keep exploring

Guides from other topics

All topics →