EDC and Pocket Knives

Knife Blade Shapes Explained: Drop Point, Tanto, Clip Point and More

Drop point vs tanto, plus clip point, sheepsfoot, wharncliffe, spear point and more: how each blade shape cuts, what it suits, and how it sharpens.

On this page
  1. Blade anatomy terms
  2. Drop point vs tanto
  3. Clip point
  4. Sheepsfoot
  5. Wharncliffe
  6. Spear point
  7. Trailing point
  8. Hawkbill and spey
  9. Blade shape by task
  10. Sharpening different shapes

Blade anatomy terms

A few terms make blade shapes easier to compare:

  • Tip / point: the very end of the blade. Fine tips pierce and do detail work well. Thicker tips are stronger.
  • Belly: the curved part of the edge. More belly means smoother slicing and rocking cuts.
  • Spine: the unsharpened back of the blade.
  • Edge: the sharpened cutting side.

Every blade shape is a trade-off between these. More belly gives better slicing. A finer tip gives better precision but is more fragile. A straighter edge gives more control and push-cutting power.

Drop point vs tanto

Drop point

On a drop point, the spine slopes gently down to meet the tip, so the point sits roughly level with or a little above the center of the blade. The result is a strong tip, a useful belly and a continuous curved edge.

  • Good at: general slicing, food prep, skinning, cutting rope and cord, and everyday utility
  • Less good at: very fine piercing, compared with clip points and needle-like tips
  • Sharpening: straightforward, because it’s one continuous curve

The drop point is the most common EDC shape for a reason. It does nearly everything reasonably well. A modified drop point adds subtle changes, such as a slightly finer tip or a swedge (a bevel ground on the spine).

Tanto

The tanto in modern pocket knives, often called the American tanto, has a mostly straight main edge that meets a short, angled front edge at a distinct corner. The tip is high and reinforced with a lot of steel behind it.

  • Good at: tip strength, piercing tough materials, scraping, and push cuts with the angled front section
  • Less good at: slicing, because there’s little or no belly, and food prep
  • Sharpening: harder, because the main edge and the front edge are sharpened as separate sections, and the corner between them needs care

The traditional Japanese tanto shape is different. It has a curved, sloping edge leading to the tip rather than a sharp angle. Most modern “tanto” folders use the American style.

Reverse tanto

A reverse tanto puts the angle on the spine instead of the edge. The spine drops at an angle toward the tip, while the edge stays a more continuous curve. You get a fine, strong tip and better slicing than an American tanto. The Benchmade 940 is a well-known example. See our best EDC knives roundup.

Which is better for EDC?

For most people, the drop point. It slices better, is easier to sharpen, and handles the widest range of everyday tasks. A tanto makes sense if your work involves a lot of piercing, scraping or hard materials, or if you simply prefer the look and the strong tip. Many users who like tantos for specific jobs still carry a drop point day to day.

Clip point

On a clip point, the spine has a concave or straight “clipped” section near the tip, which lowers the point and makes it thinner and sharper. Many traditional pocketknives and the classic Bowie knife use this shape, as do many modern folders.

  • Good at: piercing, detail work, and getting into tight spots
  • Less good at: hard prying or twisting, because the thin tip is more fragile than a drop point’s
  • Sharpening: similar to a drop point, though the fine tip needs a light touch

Sheepsfoot

A sheepsfoot has a straight edge and a spine that curves down to meet it at a blunt tip. It was traditionally used for trimming sheep’s hooves.

  • Good at: controlled cuts, box and tape opening, and slicing on a board
  • Less good at: piercing
  • Bonus: the blunt tip is less likely to cause accidental punctures

The QSP Penguin in our best EDC knives list is a popular sheepsfoot folder.

Wharncliffe

A wharncliffe also has a straight edge, but the spine tapers gradually down along its length to a sharp point, so the point sits in line with the edge.

  • Good at: precise point work, package opening, stripping and scoring
  • Less good at: slicing that needs belly, and the fine point can be fragile

Spear point

A spear point is symmetrical, with the point on the blade’s centerline. It may be sharpened on one or both edges, and double-edged versions are restricted in some places. See knife blade length and the law.

  • Good at: piercing and balanced point control
  • Less good at: slicing, compared with shapes that have more belly

Trailing point

On a trailing point, the spine curves upward so the tip sits above the spine line, leaving a long, sweeping belly.

  • Good at: skinning, filleting and long slicing cuts
  • Less good at: tip-heavy tasks, as the upswept tip can be delicate

Hawkbill and spey

  • Hawkbill: the edge curves inward like a talon. It’s excellent for pulling cuts through rope, carpet, linoleum and pruning, but awkward for general use and tricky to sharpen.
  • Spey: a mostly straight edge that curves up sharply to a blunt tip, traditionally used on livestock. It’s found on many traditional multi-blade pocketknives and some modern folders.

Blade shape by task

Task Good shapes
General everyday carry Drop point, modified drop point, reverse tanto
Boxes, tape, packaging Sheepsfoot, wharncliffe, drop point
Food prep Drop point, sheepsfoot
Piercing and detail work Clip point, wharncliffe, spear point
Scraping and tough materials Tanto
Hunting and skinning Drop point, trailing point, clip point
Rope, carpet, pruning Hawkbill

Sharpening different shapes

  • Continuous curves (drop point, clip point, trailing point): sharpen in one smooth sweep, lifting the handle slightly as you reach the belly to keep the angle consistent.
  • Straight edges (sheepsfoot, wharncliffe): among the easiest to sharpen. Keep the edge flat against the stone.
  • Tanto: sharpen the main edge and the front edge as two separate sections, and take care not to round off the corner where they meet.
  • Hawkbill: usually needs a rod or tapered sharpener to reach the inside curve.

Blade shape is one part of choosing a knife. The lock and the opener matter too. See pocket knife lock types explained and flipper vs thumb stud vs thumb hole.

The complete guide to edc and pocket knives

Best EDC Knives: Top Everyday Carry Picks
Read the guide

Keep exploring

Guides from other topics

All topics →