Knife Sharpening

How to Sharpen a Knife With a Whetstone, Step by Step

A clear, step-by-step guide to sharpening a knife on a whetstone: setup, finding the angle, raising and removing a burr, testing the edge, and fixing problems.

On this page
  1. What you need
  2. Before you start: soak or splash, and set up
  3. Step 1: Check the knife and choose your starting grit
  4. Step 2: Find the angle with a marker
  5. Step 3: Get a safe, steady grip
  6. Step 4: Sharpen the first side in sections
  7. Step 5: Raise a burr along the whole edge
  8. Step 6: Sharpen the second side
  9. Step 7: Refine on a finer stone
  10. Step 8: Remove the burr
  11. Step 9: Test the edge
  12. Step 10: Clean up and flatten the stone
  13. Single-bevel knives and left-handed sharpening
  14. Troubleshooting
  15. How often should you sharpen?
  16. Common questions

What you need

  • A medium whetstone, around 1000 grit. This does most of the work.
  • A finer stone (optional), around 3000–6000 grit, to refine the edge.
  • A coarse stone (optional), around 220–400 grit, only for chipped or very dull knives.
  • A stone holder, non-slip base or damp towel to stop the stone moving.
  • Water in a small container or spray bottle.
  • A permanent marker for checking your angle.
  • A flattening plate or coarse diamond plate, to keep the stone flat.
  • A strop (optional) for the final cleanup.

If you’re still choosing stones, our guide to whetstones and which grit to use suggests simple setups.

Before you start: soak or splash, and set up

Soaking stones need to absorb water before use. Many makers suggest about 10–15 minutes, or until air bubbles stop rising. Some recommend longer, so follow the instructions for your stone. Splash-and-go stones only need water splashed on the surface, and many shouldn’t be left soaking. If you’re not sure which you have, check the maker’s instructions.

Set the stone on its holder or a damp towel, on a stable counter at a comfortable height. Most people point the long side of the stone away from them. Some angle it slightly. Keep water nearby. The surface should stay wet throughout, and the grey slurry that builds up is normal. It helps the stone cut.

Step 1: Check the knife and choose your starting grit

Look along the edge under good light. A dull edge reflects light as a bright line or bright spots. Chips show as notches.

  • Chips, a broken tip, or very dull (it slides off a tomato skin): start on a coarse stone.
  • Dull but undamaged: start at 1000.
  • Still fairly sharp, just needs a refresh: you may only need the fine stone or a strop.

Starting coarser than you need removes steel for no benefit.

Step 2: Find the angle with a marker

Colour the edge bevel on one side with a permanent marker. Lay the knife on the stone, lift the spine to your best guess at the angle, and make one or two light strokes.

  • Ink gone evenly across the bevel: you’re matching the existing angle.
  • Ink gone only at the very edge: lower the spine slightly.
  • Ink gone only at the top of the bevel: raise the spine slightly.

Most kitchen knives are 15–20° per side. Our guide to sharpening angles has a table for estimating the angle from spine height, and our kitchen knife angle chart lists typical angles by knife.

Step 3: Get a safe, steady grip

  • Dominant hand on the handle. Many people rest the index finger on the spine or the thumb on the flat of the blade for control.
  • Two or three fingertips of the other hand on the blade face, near the edge, over the part that’s touching the stone. These fingers apply gentle pressure and help steady the angle.
  • Keep fingertips flat on the blade face, never hanging over the edge.
  • Lock your wrists and move from the arms and shoulders. Most angle wobble comes from the wrists rolling.

Step 4: Sharpen the first side in sections

Rather than trying to do the whole edge at once, work in sections: heel, middle, then tip.

  1. Place the section of edge you’re working on the stone, at your angle.
  2. Move the knife back and forth along the length of the stone with light, even pressure, keeping the angle fixed. Many sharpeners press slightly on one direction of the stroke and lighten on the return. Either way, keep it gentle.
  3. Use as much of the stone’s surface as you can, so it wears evenly.
  4. Shift your fingertips along the blade as you move to the next section.

At the curved belly and tip, lift the handle slightly as you go so the curved part of the edge stays in contact with the stone. Keep the spine at the same height. Lifting the spine at the tip is how tips get rounded.

Step 5: Raise a burr along the whole edge

Keep going on the first side until you can feel a burr: a thin lip of steel pushed over to the opposite side of the edge.

To check, draw your fingertip gently across the edge on the opposite side, moving from the spine toward the edge and off it, never along it. A slight catch or roughness at the edge means the burr has formed. Check the heel, middle and tip. The burr needs to run the full length before you move on. Any section without one hasn’t been sharpened to the edge yet.

On a dull knife this can take a few minutes at 1000 grit. If you aren’t getting a burr after a lot of work, see the troubleshooting section below, or our full guide on how to raise, feel and remove a burr.

Step 6: Sharpen the second side

Turn the knife over and repeat, at the same angle, until a burr forms along the whole edge on the first side. The second side often goes a little faster. Re-wet the stone whenever it starts to look dry.

Step 7: Refine on a finer stone

If you have a finer stone, move to it. Rinse the knife first so no coarse grit carries over. Repeat the process with lighter pressure and fewer strokes. The burr will be smaller and harder to feel on fine stones, so you can also rely on stroke counts: do roughly the same number on each side, then alternate.

Step 8: Remove the burr

A burr left on the edge makes a freshly sharpened knife feel dull, and it breaks off in use, leaving a ragged edge. To remove it:

  • Alternate single, light strokes on each side, reducing the pressure until you’re using little more than the weight of the knife.
  • Finish with a few very light edge-leading strokes, as if slicing a thin layer off the stone.
  • Strop if you have one, pulling spine-first with light pressure. Our guide to strops for Japanese knives covers technique that works for any kitchen knife.

Step 9: Test the edge

  • Paper: hold a sheet of printer paper by one corner and slice down through it. A sharp knife cuts cleanly without snagging. Snags point to a dull or damaged section.
  • Tomato or onion: a sharp knife bites into the skin without sliding.
  • Light check: look straight down at the edge under a bright light. A properly sharpened edge shows no bright reflections.

Don’t test by running a finger along the edge.

Step 10: Clean up and flatten the stone

  • Wash and dry the knife to remove metal particles and slurry.
  • Rinse the stone and let it air dry fully before storing. Soaking stones can take a day or more to dry.
  • Flatten the stone every few sessions, or whenever you can see a dip. Draw a pencil grid on the surface, rub it on a flattening plate or coarse diamond plate until the grid disappears, then rinse.

Single-bevel knives and left-handed sharpening

Single-bevel Japanese knives (yanagiba, deba, usuba) are sharpened mostly on the bevel side, with the bevel laid flat on the stone. The back is only touched lightly, kept flat, to remove the burr. Don’t use the marker-guided angle method from Step 2 to choose a new angle. Follow the existing bevel.

Left-handed sharpeners can follow the same steps with hands swapped. Left-handed users who own single-bevel knives should make sure the knife was made for left-handed use, since the bevel is on the opposite side.

Troubleshooting

Problem Likely cause What to try
No burr after lots of strokes Angle lower than the existing bevel; or the knife was very dull Re-check with the marker; raise the angle slightly; switch to a coarser stone
Burr only in some sections Uneven pressure or angle; tip or heel missed Work in shorter sections; lift the handle at the curve
Edge still dull after sharpening Burr not removed, or rounded by inconsistent angle Deburr with lighter alternating strokes; slow down and lock your wrists
Wide, uneven or wavy bevel Angle drifting between strokes Use the marker often; try an angle guide while learning
Rounded tip Spine lifting at the tip Keep the spine height steady; lift the handle instead
Knife catching or digging into the stone Stone too dry or not flat Re-wet; flatten the stone

How often should you sharpen?

It depends on the knife and how much you cook. Many home cooks find a full whetstone session every few months is enough, with honing or stropping in between. If the knife slides on tomato skin or crushes herbs instead of slicing them, it’s time.

Common questions

Does a whetstone need to be wet? Water stones do. Keep the surface wet the whole time. Oil stones use honing oil instead, and most diamond plates can be used with water or dry. Follow the maker’s guidance.

How many strokes per side? There’s no fixed number. Sharpen until a burr forms along the whole edge, then match the other side. On a fine stone, using similar stroke counts on each side is a reasonable guide.

Push or pull? Both work. What matters is a steady angle and light, even pressure.

What angle do I use for my brand? See our list of sharpening angles by brand.

The complete guide to knife sharpening

Best Knife Sharpening Angle: 15 vs 20 Degrees
Read the guide

Keep exploring

Guides from other topics

All topics →