What counts as a carbon steel for knives
In knife terms, a carbon steel is a steel that relies mainly on carbon for its hardness and contains too little chromium to be stainless. That includes plain carbon steels such as 1084 and 1095, and low-alloy steels such as 5160, 52100 and 80CrV2 that add small amounts of chromium, vanadium or other elements.
Carbon knife steels generally share a few traits: they are relatively easy to sharpen, can take very keen edges, are often tough at typical hardness, and will rust or patina without care. For how they compare with stainless as a group, see carbon steel vs stainless steel knives.
How the numbers work (AISI/SAE naming)
Many American carbon and alloy steels use a four-digit AISI/SAE number.
- The first two digits indicate the alloy family. 10xx is plain carbon steel. 51xx is a chromium steel. 52xxx is a higher-carbon chromium bearing steel.
- The last two digits (or three, for 52100) give the approximate carbon content in hundredths of a percent. So 1095 has roughly 0.95% carbon, 1084 roughly 0.84%, and 5160 roughly 0.60%.
Tool steels such as O1 and W2 use a different letter-based system (O for oil-hardening, W for water-hardening), and European and Japanese steels have their own names.
The common carbon knife steels
Compositions below are approximate typical values; specifications allow ranges.
1075, 1080 and 1084
These plain carbon steels contain around 0.75–0.85% carbon and very little else. They are widely recommended for beginner bladesmiths because they tolerate simple heat treatment well and are inexpensive. 1084 in particular is popular for first knives and for pattern-welded (Damascus) billets. They make tough, easy-to-sharpen blades with moderate edge retention.
1095
1095 has roughly 0.95% carbon and is one of the most widely used carbon steels in factory knives, including many outdoor, survival and traditional pocket knives. It can be hardened to a high level and takes a keen edge. It is somewhat less forgiving to heat treat than 1084 and rusts readily. Variants such as 1095 Cro-Van add small amounts of chromium and vanadium.
5160
5160 is a chromium spring steel with about 0.6% carbon and roughly 0.7–0.9% chromium. It is used for vehicle leaf springs and is valued in knives for toughness. It is common in swords, large choppers, machetes and axes, usually at somewhat lower hardness than a slicing knife. Its lower carbon means less edge retention than 1095 at similar use.
52100 (ball bearing steel)
52100 was developed for ball and roller bearings. It has about 1% carbon and around 1.3–1.6% chromium, still far below stainless levels. It is known for a fine structure, good toughness for its hardness, and a keen edge, and it is popular in forged hunting and kitchen knives, often around 60–62 HRC. We cover it in depth in is 52100 steel good for knives?
80CrV2
80CrV2 is a European steel with about 0.8% carbon plus small amounts of chromium and vanadium. It sits close to 1080/1084 in behaviour but with a little extra hardenability and grain refinement. It is a common choice for bushcraft knives, choppers and beginner forging.
O1 and W2
O1 is an oil-hardening tool steel with roughly 0.9% carbon plus manganese, chromium and a little tungsten. It is well known among woodworkers and knifemakers for taking a fine edge and is used in many bushcraft knives. W2 is a water-hardening tool steel with around 1% carbon and a little vanadium. Smiths like it for differentially hardened blades that show a visible hamon line.
15N20
15N20 is a carbon steel with roughly 0.75% carbon and about 2% nickel. On its own it makes a tough blade, but it is best known as the bright layer in pattern-welded steel, usually paired with 1084 or 1095. The nickel resists etching, which creates the contrast.
Japanese carbon steels: white, blue and SK
Japanese kitchen knives often use carbon steels from Proterial (formerly Hitachi Metals):
- White steel (shirogami) #1 and #2: very pure carbon steels with minimal alloying, prized for an extremely keen edge and easy sharpening.
- Blue steel (aogami) #1 and #2: white steel with added chromium and tungsten, giving somewhat better edge retention.
- Blue Super (aogami super): further alloyed with molybdenum and vanadium for more wear resistance.
SK steels (such as SK-5 / SK85) are Japanese carbon tool steels, broadly similar to American 10xx grades, used in many budget and mid-priced blades.
Comparison table
| Steel | Approx. carbon | Notable alloying | Strengths | Common uses |
|---|---|---|---|---|
| 1084 | 0.84% | Minimal | Forgiving heat treat, tough, cheap | Beginner forging, Damascus |
| 1095 | 0.95% | Minimal | Keen edge, hardens well | Outdoor, survival, traditional folders |
| 5160 | 0.60% | ~0.8% Cr | Very tough | Swords, choppers, axes |
| 52100 | 1.0% | ~1.5% Cr | Fine edge, good toughness for hardness | Hunters, kitchen knives |
| 80CrV2 | 0.80% | Cr, V | Tough, forgiving | Bushcraft, choppers |
| O1 | 0.90% | Mn, Cr, W | Fine edge | Bushcraft, woodworking tools |
| W2 | ~1.0% | Small V | Shows a hamon | Differentially hardened blades |
| White #2 | ~1.0–1.1% | Very pure | Exceptionally keen edge | Japanese kitchen knives |
| Blue #2 | ~1.0–1.1% | Cr, W | Keen edge, more wear resistance | Japanese kitchen knives |
5160 vs 1084: key differences
These are two of the most popular forging steels, and they suit different blades.
- Carbon content: 1084 has more carbon (about 0.84% vs about 0.60%), so it can reach higher hardness and generally holds an edge somewhat longer.
- Alloying: 5160 adds chromium (and more manganese), which increases hardenability, so it hardens a little more readily in thicker sections and is slightly less fussy about quench speed than 1084.
- Toughness: 5160 is generally regarded as the tougher of the two, which is why it is a favourite for swords, large choppers and anything that will see impact.
- Typical use: 1084 is a classic for general-purpose knives, hunters and Damascus. 5160 suits long blades and hard-use choppers.
Both are good beginner steels. The choice mostly comes down to whether you want a bit more edge retention (1084) or a bit more toughness (5160).
Is bearing steel good for knives?
Yes. 52100 bearing steel is a well-regarded knife steel when properly heat treated. The caveat is salvaged material: old bearings and races are not always 52100 (some bearings use other grades, including stainless and case-hardened steels). Recycled parts may also be fatigued or cracked, and the hardened steel has to be fully annealed before shaping. Many knifemakers prefer to buy new 52100 bar stock with a known specification. Forging a blade from a reclaimed bearing can still be a satisfying project if you accept some uncertainty.
What carbon steel do Case knives use?
W.R. Case & Sons uses a carbon steel it calls Chrome Vanadium (CV) for many traditional pocket knives. It is a carbon steel with small amounts of chromium and vanadium, often compared to 1095 in how it sharpens and behaves. Like other carbon steels, it develops a patina and needs to be kept dry. Case also offers stainless options under its Tru-Sharp name.
What is the most common type of carbon steel?
Across all industry, low-carbon (“mild”) steels, typically with less than about 0.25–0.3% carbon, are the most widely produced and used for structural steel, sheet and many manufactured goods. Mild steel cannot be hardened enough for a useful knife edge. Among knife steels specifically, 1095 is one of the most widely seen carbon grades in factory knives.
Choosing a carbon steel
- For a first forged knife: 1084 or 80CrV2.
- For a tough chopper or long blade: 5160 or 80CrV2.
- For a keen, easily maintained hunter or kitchen knife: 52100, 1095, O1, or Japanese white or blue steel.
- For pattern-welded steel: 1084 or 1095 with 15N20.
Whatever the grade, heat treatment largely decides how the finished blade performs. For how carbon steels fit alongside stainless and powder steels, see our guide to the best knife steel.