Knife Steel

VG10 Steel for Knives: Is It Any Good?

VG-10 is a Japanese cobalt stainless steel used in many chef's and pocket knives. Learn its composition, hardness, strengths, weaknesses and how it compares.

On this page
  1. Short answer: is VG-10 good knife steel?
  2. What VG-10 is
  3. How VG-10 performs
  4. VG-10 compared with other steels
  5. VG-10 in kitchen knives vs pocket knives
  6. Brands that use VG-10
  7. Caring for a VG-10 knife
  8. VG-10 vs G-10: not the same thing
  9. Who should (and shouldn’t) choose VG-10

Short answer: is VG-10 good knife steel?

Yes. VG-10 is a well-established, good-quality stainless steel, especially for kitchen knives. It takes a keen edge, holds it longer than typical German kitchen steels, resists rust well and is not especially hard to sharpen. Its main weakness is that, at the high hardness Japanese makers usually run it, it can chip if twisted, used on bone or frozen food, or dropped.

It is no longer the top performer it once was among pocket knife steels. Newer powder steels outperform it on edge retention. For kitchen use, though, it remains a solid, proven choice.

What VG-10 is

VG-10 (sometimes written VG10, short for “V Gold 10”) is a stainless steel made by Takefu Special Steel in Echizen, Japan, a region known for cutlery. It was developed with kitchen knives in mind and later spread to pocket and outdoor knives.

Composition

Published figures vary a little by source. Typical approximate values are:

Element Approximate content Main role
Carbon ~1.0% Hardness and wear resistance
Chromium ~15% Corrosion resistance
Molybdenum ~1% Corrosion resistance, hardenability
Cobalt ~1.3–1.5% Strengthens the steel’s matrix
Vanadium ~0.1–0.3% Grain refinement, some wear resistance
Manganese ~0.5% Hardenability

The cobalt addition is one of VG-10’s signatures. Few mainstream knife steels include it.

Typical hardness

VG-10 is commonly heat treated to roughly 59–61 HRC, and some kitchen knife makers run it a little higher. That is harder than most German-style kitchen knives (often around 56–58 HRC), which is part of why it holds a finer edge. See knife hardness explained for what those numbers mean in practice.

VG-10 as a clad core (“Damascus” VG-10)

Many VG-10 kitchen knives are made as laminated blades: a hard VG-10 core forms the cutting edge, sandwiched between softer stainless layers. Etching these layers produces the wavy pattern often sold as “Damascus.” The cladding makes the blade more resilient and gives it the look, but the cutting is done by the VG-10 core.

How VG-10 performs

Sharpness and edge retention

VG-10’s fairly fine structure lets it take a keen edge at the acute angles used on Japanese-style knives. It typically holds that edge noticeably longer than softer stainless steels such as X50CrMoV15 or 420-series steels. Wear-resistant powder steels such as SG2/R2, S35VN, M390 or MagnaCut generally hold an edge longer still.

Toughness and chipping

VG-10’s toughness is moderate. At around 60 HRC with a thin edge, it is more likely to microchip than a softer German knife if you cut through bone, pry at squash, twist the blade or chop on a hard surface. Used on a wood or plastic board with a slicing or push-cutting technique, chipping is usually not a problem.

Corrosion resistance

With around 15% chromium plus molybdenum, VG-10 resists rust well in normal kitchen use. It is still not rustproof. Leaving it wet, especially with salty or acidic residue, can cause spotting, and dishwashers are best avoided.

Sharpening

Competitor reviews disagree here: some call VG-10 easy to sharpen, others say it’s demanding. In practice, it sits in the middle. It takes more effort than soft German stainless or simple carbon steel but is much easier than high-vanadium powder steels. Ordinary waterstones work well. Some users find VG-10 can form a stubborn burr, so finishing with light, alternating strokes and a strop helps.

VG-10 compared with other steels

Ratings are relative and assume typical heat treatment.

Steel Edge retention Chip resistance Corrosion resistance Ease of sharpening
X50CrMoV15 (German) Moderate High Good Very easy
14C28N / AEB-L Moderate High Good Easy
VG-10 Good Moderate Good Moderate
SG2 / R2 (powder) Very good Moderate Good Moderate–hard
S35VN Good–very good Moderate–good Good Moderate
MagnaCut Good–very good Good Very good Moderate

Against German X50CrMoV15, VG-10 trades some forgiveness for a finer, longer-lasting edge. Against 14C28N or AEB-L, VG-10 can hold an edge somewhat longer at higher hardness, while those steels are generally tougher and quicker to sharpen. For how powder steels compare, see S30V vs S35VN vs S45VN and MagnaCut steel explained.

VG-10 in kitchen knives vs pocket knives

In the kitchen, VG-10’s balance of keenness, edge life and stain resistance is a good fit, and it remains one of the most common steels in mid-priced Japanese-style knives.

In pocket knives, VG-10 was once a premium choice. Spyderco used it widely in models such as earlier versions of the Delica and Endura. Today it is usually considered a good mid-range steel rather than a high-end one, as powder steels have become common in folders at similar prices.

Brands that use VG-10

VG-10 appears in knives from many makers, including Shun (in its Classic line), Tojiro (DP series), various Miyabi lines and many smaller Japanese brands, as well as Spyderco and Fallkniven (which uses laminated VG-10 in several models). Product lines change, so check the specific model’s listed steel.

Caring for a VG-10 knife

  • Wash by hand and dry promptly. Avoid the dishwasher.
  • Use a wood or plastic cutting board, not glass, stone or ceramic.
  • Avoid twisting, prying, bones and frozen foods.
  • For honing, a fine ceramic rod or a strop is gentler on a hard edge than a coarse steel.
  • Sharpen on waterstones or similar, keeping a consistent angle.

VG-10 vs G-10: not the same thing

The names are easy to confuse. VG-10 is a blade steel. G-10 is a handle material made from layers of fiberglass cloth bonded with resin. G-10 is popular on pocket and outdoor knives because it is durable, light, grippy and unaffected by water. A knife can easily have a VG-10 blade and G-10 handle scales.

Who should (and shouldn’t) choose VG-10

VG-10 is a good fit if you:

  • want a stainless kitchen knife that holds a finer edge than typical German knives
  • cut on a proper board with a controlled technique
  • are comfortable sharpening on stones or using a sharpening service

Consider something else if you:

  • use your knives roughly, on bones or hard foods: a softer German knife may suit you better
  • want the longest edge life from a pocket knife: look at modern powder steels
  • want the easiest possible sharpening: 14C28N, AEB-L or carbon steels may suit you better

For a wider view of how VG-10 fits among other steels, see our guide to the best knife steel.

The complete guide to knife steel

Best Knife Steel: What Metal Makes a Good Blade
Read the guide

Keep exploring

Guides from other topics

All topics →