Knife Sharpening

Best Knife Sharpening Angle: 15 vs 20 Degrees

15 or 20 degrees? How sharpening angle affects sharpness and durability, an angle chart by knife type, and how to find and hold the right angle by hand.

On this page
  1. The short answer
  2. Per-side angle vs inclusive angle
  3. 15 vs 20 degrees: what actually changes
  4. How steel hardness affects the choice
  5. Sharpening angle chart by knife type
  6. How to find the angle your knife already has
  7. How to hold an angle by hand
  8. Changing angles: lowering, raising and micro-bevels
  9. What happens if you sharpen at the wrong angle
  10. Common questions

The short answer

Most double-bevel knives are sharpened somewhere between 15 and 20 degrees per side.

  • About 15° per side suits thinner, harder blades used for slicing: most Japanese kitchen knives and many modern Western chef’s knives.
  • About 20° per side suits softer or thicker blades and harder use: traditional German-style knives, budget kitchen knives, and most pocket knives.

If you don’t know which to pick, the safest choice is usually the angle the knife already has. Matching the existing bevel removes the least steel and gets you sharp fastest. Holding that angle steadily matters more than whether the number is exactly 15 or 17 or 20.

The rest of this guide explains what the numbers mean, how to choose between them, and how to find and hold an angle when you’re sharpening by hand.

Per-side angle vs inclusive angle

Sharpening angles are usually quoted per side: the angle between one face of the edge bevel and the centre line of the blade. On a symmetrical double-bevel knife, the total (inclusive) angle is double that.

Per side Inclusive (total) Typical use
12° 24° Very fine slicing edges on hard Japanese steel
15° 30° Japanese knives, many modern Western kitchen knives
17° 34° A middle ground for mixed kitchen use
20° 40° German-style and budget kitchen knives, pocket knives
25° 50° Outdoor, hunting and heavy-use blades

This matters when you read packaging. A sharpener labelled “30°” may mean 15° per side, and a knife spec of “15°” almost always means per side. If a number seems strangely high or low, check which one is being used.

Single-bevel Japanese knives (such as a yanagiba or deba) don’t follow this pattern. They’re sharpened mostly on one side, so the per-side and inclusive language doesn’t map neatly. For those, follow the existing bevel.

15 vs 20 degrees: what actually changes

A lower angle puts less steel directly behind the cutting edge. That makes the edge enter food with less resistance, and it also makes it less able to stand up to sideways force, bone, frozen food or a hard cutting board.

~15° per side ~20° per side
Edge thickness Thinner Thicker
Cutting effort Lower; glides through soft food Slightly more effort
Edge stability Less; more prone to rolling or chipping More; tolerates rougher use
Sharpening a dull knife Can take longer if the knife started wider Often quicker on a Western knife
Typical knives Japanese gyuto and santoku, many current Western chef’s knives, fillet knives German-style chef’s knives, inexpensive kitchen knives, pocket and utility knives

Neither angle is “better” in general. A 15° edge on a knife that’s used for prying open squash and chopping through chicken backs will dull and damage quickly. A 20° edge on a thin Japanese slicer throws away much of what makes that knife pleasant to use.

For a closer look at the sharpness question specifically, see whether 15 or 20 degrees is sharper.

How steel hardness affects the choice

The steel decides how thin an edge can be and still hold up.

  • Softer stainless steels (common in German-style and budget knives) tend to roll or fold when the edge is very thin. These usually do better at around 18–20° per side, although many good Western knives now ship closer to 15°.
  • Harder steels (common in Japanese knives) can support a thinner edge without rolling as quickly, which is why 15° or less is normal for them. The trade-off is that very hard steel at a very low angle can chip rather than roll if it hits something hard or is twisted in the cut.

The geometry behind the edge matters too. A thin blade sharpened at 20° can still cut better than a thick blade sharpened at 15°. The edge angle is only the last fraction of a millimetre of the knife’s shape.

Sharpening angle chart by knife type

These are typical ranges, not rules. If the maker publishes an angle, use theirs.

Knife type Typical angle per side
Japanese double-bevel kitchen knives (gyuto, santoku, petty) 10–15°
Modern Western chef’s knives (many current German and American brands) 14–17°
Traditional German-style or budget kitchen knives 18–20°
Fillet and boning knives 15–20°
Meat cleavers 20–25° or more
Pocket and everyday-carry knives 17–22°
Hunting and outdoor fixed blades 20–25°
Choppers, machetes, axes 25–30° or more

For factory angles from specific makers, see our list of sharpening angles by brand. For the kitchen drawer in particular, including bread knives and single-bevel Japanese knives, see what angle kitchen knives should be sharpened at.

How to find the angle your knife already has

  1. Check the maker’s information. Many brands publish a factory angle in care instructions or on their website.
  2. Use the marker test. Colour the edge bevel on one side with a permanent marker. Lay the knife on your stone at the angle you think is right and make one or two light strokes.
  3. Read the result.
    • Ink removed evenly across the whole bevel: your angle matches.
    • Ink removed only at the very edge: you’re holding the knife too high (a steeper angle than the bevel).
    • Ink removed only at the top of the bevel, away from the edge: you’re holding it too low.
  4. Adjust and repeat until the ink comes off evenly, then remember how that position feels.

The marker test works on whetstones, diamond plates and guided systems. It’s also the quickest way to find out whether a knife’s previous owner (or a pull-through sharpener) has changed the bevel.

How to hold an angle by hand

The spine-height method

Lay the blade flat on the stone, then lift the spine. The height of the spine above the stone sets the angle. For a flat-sided blade, the lift you need is roughly the blade’s height (edge to spine) multiplied by the sine of the angle.

Blade height (edge to spine) Lift spine for ~15° Lift spine for ~20°
25 mm (1 in), e.g. paring or pocket knife about 6.5 mm about 8.5 mm
40 mm (1.6 in), e.g. utility or petty knife about 10 mm about 13.5 mm
50 mm (2 in), e.g. chef’s knife about 13 mm about 17 mm

These are approximations. Blade thickness and taper change the real angle slightly, and blade height shrinks toward the tip, so you’ll need to lower the spine a little as you move toward the point to keep the same angle. Use the numbers to get close, then confirm with the marker test.

Folded paper and angle guides

  • Folded paper: fold a square sheet corner to corner to get 45°, fold again for about 22.5°, and once more for about 11°. Halfway between the last two is close to 15–17°. Use the paper as a visual check beside the stone, not something to press the blade against.
  • Clip-on angle guides attach to the spine and hold it at a fixed height. They’re helpful while you build muscle memory, though they can scratch the blade face.
  • Guided systems and rolling sharpeners hold the angle mechanically. They’re the most consistent option if freehand sharpening isn’t for you.

Whatever you use, a steady 18° is better than an edge that wanders between 13° and 22°. A wobbly angle rounds the edge and it may never come to a clean apex.

Changing angles: lowering, raising and micro-bevels

Lowering the angle (say from 20° to 15°) means grinding away the shoulder of the old bevel until the new, wider bevel meets at the edge. On a Western chef’s knife that can take a lot of work on a coarse stone. It’s called reprofiling, and it’s worth doing deliberately rather than by accident.

Raising the angle (say from 15° to 20°) is quick. The first strokes only touch the very edge, creating a small, steeper bevel. Each later sharpening at that angle makes the new bevel a little wider.

A micro-bevel is that small, slightly steeper bevel used on purpose. Some sharpeners finish a 15° edge with a few light strokes at about 17–20°. It can make a thin edge more stable and quicker to touch up, at a small cost in keenness.

What happens if you sharpen at the wrong angle

Sharpening at the “wrong” angle rarely ruins a knife, but it changes how it behaves:

  • A little off, but consistent: usually no problem. You’re simply setting a slightly different bevel.
  • Higher than the existing bevel: the edge becomes a little steeper and thicker each time. It stays usable but can feel less keen.
  • Lower than the existing bevel: you grind the shoulder instead of the edge. You’ll make many strokes without raising a burr, because you haven’t reached the apex yet.
  • Inconsistent: rocking the angle produces a rounded edge that doesn’t come fully sharp, even after a lot of work.

Fixed-angle tools can create the same problems if their angle doesn’t match the knife. A pull-through set at 20° will slowly turn a 15° knife into a 20° knife. There’s more on that in our piece on whether pull-through sharpeners are bad for your knives.

Common questions

Do you push or pull when sharpening a knife?

Both work. On a whetstone, most people use back-and-forth strokes or sweep the edge across the stone in one direction. What matters is a steady angle, light, even pressure, and covering the whole edge from heel to tip. Our step-by-step whetstone guide shows both approaches. On a strop, you only pull, with the spine leading, so the edge doesn’t cut into the leather.

Can I use WD-40 to sharpen knives?

WD-40 doesn’t sharpen anything. Some people use it as a lubricant on oil stones, but it isn’t made as a honing oil and it isn’t something you want on a knife used for food. Use what the stone is designed for: water on water stones, honing oil or food-grade mineral oil on oil stones, and water or nothing on most diamond plates. Then wash the knife before you cook with it.

What is the last thing you should do after sharpening?

Make sure the burr is gone, then clean the knife. Sharpening leaves a thin, flexible lip of steel on the edge (the burr) and fine metal particles on the blade. Remove the burr with light alternating strokes or a strop, then wash and dry the knife. See how to raise, feel and remove a burr for the details. If you use a strop, our guide to strops for Japanese knives covers technique.

What angle should I use for a budget Western brand like Chicago Cutlery?

If the maker’s care information gives an angle, use it. If it doesn’t, about 20° per side is a reasonable, durable default for most inexpensive Western kitchen knives. Use the marker test to check what’s already on the blade before you commit. For a quicker decision guide across every knife type, see what’s the best angle to sharpen a knife.

Keep exploring

Guides from other topics

All topics →