Short answer
CPM MagnaCut is a powder metallurgy stainless steel designed specifically for knives. It is popular because it combines three properties that usually pull against each other: high toughness for a stainless steel, good edge retention and very good corrosion resistance. It doesn’t lead every category, but few steels do as well across all three at once, which is why many makers now offer it.
What MagnaCut is
MagnaCut was designed by metallurgist Dr. Larrin Thomas, known for the Knife Steel Nerds website, and was released by Crucible Industries in 2021. Unlike most knife steels, which were adapted from industrial tooling, it was designed from the start around what a knife blade needs.
Composition
Approximate published nominal composition:
| Element | Approximate content |
|---|---|
| Carbon | ~1.15% |
| Chromium | ~10.7% |
| Vanadium | ~4.0% |
| Niobium | ~2.0% |
| Molybdenum | ~2.0% |
| Nitrogen | ~0.2% |
Some online sources list different figures, such as higher chromium. The values above match the commonly published nominal specification.
Why it performs differently
Most stainless knife steels contain chromium carbides. Those carbides add wear resistance, but they also tie up chromium that would otherwise protect against rust, and relatively large chromium carbides can reduce toughness.
MagnaCut’s design avoids chromium carbides. Instead, it relies on vanadium and niobium carbides, which are harder and can be kept small and evenly distributed. That has two effects:
- More of the chromium stays dissolved in the steel, so corrosion resistance is high even though total chromium is relatively low.
- With smaller carbides and a cleaner structure, toughness is higher than most stainless steels with similar wear resistance.
How MagnaCut performs
Toughness
In its designer’s published testing, MagnaCut’s toughness was comparable to CPM 4V, a non-stainless tool steel known for toughness, and well above many popular stainless steels such as S35VN and 20CV/M390 at similar hardness. In practice, that means better resistance to edge chipping and blade breakage than most stainless knives.
Corrosion resistance
MagnaCut rated as highly corrosion resistant in its designer’s testing, ahead of many common premium stainless steels. It is a good choice for humid climates, fishing and hunting. It is still not as close to rustproof as specialist steels such as LC200N or H1, so rinsing and drying after saltwater exposure is still wise.
Edge retention
MagnaCut’s edge retention is generally described as similar to steels like S35VN, S45VN or CPM 4V at comparable hardness. It is good, but steels with more vanadium, such as S90V, or very high-hardness steels such as Maxamet, will last longer in abrasive cutting.
Sharpening
Because its carbides are small and it isn’t extremely high in carbide volume, MagnaCut is generally regarded as easier to sharpen than high-wear steels such as S90V or M390, though harder than simple steels. Diamond plates work fastest, but quality synthetic stones also work. Many users find it deburrs cleanly.
MagnaCut compared with other premium steels
Ratings are relative and assume good heat treatment at typical hardness.
| Steel | Edge retention | Toughness | Corrosion resistance | Ease of sharpening |
|---|---|---|---|---|
| MagnaCut | Good–very good | Very good (for stainless) | Very good | Moderate |
| S35VN / S45VN | Good | Moderate | Good | Moderate |
| M390 / 20CV | Very good | Moderate | Very good | Hard |
| S90V | Excellent | Low–moderate | Good | Hard |
| CPM 3V | Moderate–good | Excellent | Low–moderate | Moderate |
| 14C28N | Moderate | Good | Good | Easy |
For a closer look at the steels MagnaCut often replaces, see S30V vs S35VN vs S45VN.
Why knife makers are switching
- One steel for many knives: it suits everyday carry, hunting, fishing and outdoor knives, and even kitchen knives, so makers can standardise on it.
- Fewer warranty problems: better toughness and corrosion resistance mean fewer chipped edges and rust spots.
- Customer demand: MagnaCut has become a recognised name among buyers, and many shoppers look for it specifically.
- Workable: compared with very high-wear steels, it is reasonable to grind, finish and sharpen.
Which knives use MagnaCut?
MagnaCut is now available from many production and custom makers. Brands that have offered MagnaCut models include Benchmade, Spyderco, Buck, Leatherman and Montana Knife Company, along with many smaller makers and custom knifemakers. Specific models and availability change often, so check each product’s listed steel. Knifemaking suppliers also sell MagnaCut bar stock.
Limitations and caveats
- It isn’t the best at everything. S90V and Maxamet hold an edge longer, CPM 3V is tougher, and LC200N is more corrosion resistant. MagnaCut’s strength is balance.
- Heat treatment still matters. Its performance depends on correct heat treatment, and results vary between makers. A well-made knife in a less fashionable steel can outperform a poorly treated MagnaCut blade.
- Price. MagnaCut knives often cost more than equivalents in older steels.
- Diminishing returns for light use. If you open a few packages a week, you may not notice much difference over a good mid-range steel.
Is MagnaCut worth it?
For a hunting, fishing, outdoor or hard-working everyday carry knife, MagnaCut is one of the strongest all-round choices available, especially if you want stainless convenience without giving up toughness. For light use, or if price matters most, steels such as 14C28N, S35VN or even a good D2 may serve you just as well.
For how MagnaCut fits among all the main steel families, see our guide to the best knife steel.