Knife Sharpening

What angle should kitchen knives be sharpened at?

Most kitchen knives are sharpened at 15–20° per side. See angles for chef's, paring, boning, bread and cleaver knives, plus single-bevel Japanese knives.

On this page
  1. The short answer
  2. Kitchen knife sharpening angle chart
  3. Western vs Japanese kitchen knives
  4. Single-bevel Japanese knives
  5. Serrated and bread knives
  6. Cleavers: meat vs vegetable
  7. How to match the angle on your own knives
  8. Honing between sharpenings

The short answer

Most kitchen knives should be sharpened at 15 to 20 degrees per side.

  • Japanese double-bevel knives: usually 10–15° per side.
  • Modern Western chef’s knives: often around 15°, sometimes up to 17°.
  • Older, thicker or budget Western knives: around 20° per side.

When the maker publishes an angle, use it. When it doesn’t, match the bevel already on the knife. Two kinds of kitchen knife don’t fit this pattern at all: serrated bread knives and single-bevel Japanese knives. Both are covered below.

Kitchen knife sharpening angle chart

Knife Typical angle per side Notes
Western chef’s knife 15–20° Many current German and American knives are near 15°; older ones nearer 20°
Japanese gyuto (chef’s knife) 10–15° Harder steel supports a thinner edge
Santoku 10–15° Japanese-made usually lower; Western-made santokus often follow the brand’s chef’s knife
Nakiri (vegetable knife) 10–15° Thin push-cutting blade; avoid twisting or chopping bone
Paring and petty knives 15–20° Usually the same angle as the brand’s chef’s knife
Utility knife 15–20° As for the chef’s knife
Boning knife 15–20° A little wider if it regularly meets joints and bone
Fillet knife 15–17° Thin and flexible; prioritise slicing
Slicing and carving knife 15–17° Long, thin, used on cooked meat
Chinese vegetable cleaver 15–20° Thin blade for slicing and chopping vegetables, not bone
Meat cleaver 20–25° or more Heavy edge built to take impacts
Serrated bread knife Follow the factory bevel Usually sharpened on one side only
Single-bevel Japanese knives Follow the existing bevel Sharpened mainly on one side

For factory angles from specific makers like Zwilling, Miyabi and Cutco, see our list of sharpening angles by brand.

Western vs Japanese kitchen knives

The main reason Japanese knives use lower angles is steel hardness. Japanese kitchen knives are commonly hardened to around 60 HRC or above. Many German-style knives are softer, often in the mid to high 50s. Harder steel can hold a thinner edge without rolling, while softer steel holds up better with a little more angle.

Blade thickness plays a part too. Many Japanese knives are ground thinner behind the edge, so they’re designed around a fine edge. Sharpening a thin Japanese gyuto at 20° gives up much of what makes it pleasant to use. Sharpening a soft, thick Western knife at 12° tends to give an edge that rolls quickly.

If you have both kinds in your drawer, it’s fine to sharpen them at different angles. Using one angle for everything is simpler, but it means the Japanese knives get a thicker edge than they were designed for, or the Western knives get a more fragile one. For a fuller explanation of the trade-off, see whether 15 or 20 is sharper.

Single-bevel Japanese knives

Traditional Japanese knives such as the yanagiba (sushi and sashimi slicer), deba (fish butchery) and usuba (vegetable knife) have a single bevel. They’re ground mostly on one side, with a slightly hollow, flat back (the ura) on the other.

  • Sharpen the bevel side by laying the whole bevel flat on the stone. The blade’s own bevel sets the angle, so you don’t choose a number.
  • Touch the back side only lightly, keeping it flat on the stone, just enough to remove the burr. Don’t put a bevel on the back.
  • Avoid pull-through and most electric sharpeners, which are designed for symmetrical double-bevel edges.

Many Japanese knives sold in Western shops (most gyuto, santoku and petty knives) are double-bevel, so check before you sharpen.

Serrated and bread knives

Most serrated bread knives are beveled on one side only, with a flat back. They also dull much more slowly than straight edges because the points do most of the work. When they do need attention:

  • Use a tapered ceramic or diamond rod that fits the scallops. Work each scallop at its existing bevel angle, on the beveled side only.
  • Finish with a light pass along the flat side to remove any burr.
  • Some brands, including Cutco for its Double-D edges, recommend sending serrated knives back to them rather than sharpening at home.

Flat stones and pull-through slots meant for straight edges will grind the tips of the serrations rather than sharpen them.

Cleavers: meat vs vegetable

“Cleaver” covers two very different knives:

  • Meat cleavers are thick and heavy, built to chop through bone and joints. They need a wide, robust edge, around 20–25° per side or more. A very fine edge chips or dents on the first bone.
  • Chinese vegetable cleavers (often called cai dao) look similar but are much thinner and are used like a chef’s knife for slicing and chopping produce. They’re sharpened more like a chef’s knife, around 15–20° per side, and shouldn’t be used on bone.

How to match the angle on your own knives

  1. Colour the edge bevel with a permanent marker.
  2. Make one light stroke on your stone at your best guess.
  3. If the ink comes off the whole bevel evenly, you’ve matched it. If only the edge is cleaned, lower the spine. If only the top of the bevel is cleaned, raise it.

Our guide to sharpening angles includes a table for estimating the angle from how high you lift the spine. When you’re ready to sharpen, follow our step-by-step whetstone guide.

Honing between sharpenings

Honing straightens an edge that has bent slightly in use. It doesn’t replace sharpening, but it stretches the time between sessions.

  • Hold the knife at about the same angle it was sharpened at, or very slightly higher, and use light, alternating strokes.
  • For softer Western knives, a smooth or fine steel rod works well.
  • For hard Japanese knives, a fine ceramic rod or a leather strop is gentler. Grooved steel rods can chip hard, thin edges. See our guide to strops for Japanese knives.

If you’ve been using a pull-through sharpener and your knives feel thicker than they used to, the angle may have been changed over time. Our article on whether pull-through sharpeners are bad for your knives explains how that happens.

The complete guide to knife sharpening

Best Knife Sharpening Angle: 15 vs 20 Degrees
Read the guide

Keep exploring

Guides from other topics

All topics →