The short answer
For most Japanese kitchen knives, the best strop is firm leather glued to a flat, rigid base: a bench strop, or a paddle strop you hold steady. Use it bare to clean up the last of the burr after sharpening, or load it with a fine compound to refine the edge a little further.
Stick to light pressure and edge-trailing strokes, with the spine leading and the edge following. Firm leather on a flat base keeps the angle stable and is less likely to round the thin edge that makes Japanese knives cut so well.
Why Japanese knives need a careful strop
Most Japanese kitchen knives are made from harder steel and sharpened at lower angles than Western knives, often 15° per side or less. Our list of sharpening angles by brand has some examples. That combination cuts beautifully but has two weak points:
- Thin edges round over easily if they’re pressed into soft, springy material or stropped at too high an angle.
- Hard steel is less forgiving of sideways force. Grooved steel honing rods can chip it, which is why many owners strop or use a fine ceramic rod instead.
A strop works the very edge gently. Done well, it removes the tiny remnants of burr left by the stone and leaves a cleaner, more durable apex. Done badly, with too much pressure or the wrong angle, it dulls the knife.
Types of strop
| Type | Description | Good for | Watch out for |
|---|---|---|---|
| Bench strop | Leather or another substrate glued to a wood or plastic block that sits on the counter | Kitchen knives, especially long blades; the most stable option | Takes up some space |
| Paddle strop | A smaller strop on a handle, often two-sided | Small knives, quick touch-ups, travel; two sides allow bare + compound | Harder to keep the angle steady with a long gyuto |
| Hanging strop | A loose strap anchored at one end, pulled taut | Straight razors | Leather flexes under the blade and rounds thin kitchen edges; not recommended for Japanese knives |
| Balsa or wood strop | Thin balsa or hardwood, usually loaded with diamond compound | Very hard steels; very little give, so minimal rounding | Needs compound to do much |
| Improvised (newspaper, cardboard, denim on a board) | Flat material on a hard surface | Burr removal in a pinch | Less consistent than proper leather |
Leather and substrate choices
- Smooth cowhide is the most common and a good default. It’s firm enough for kitchen knives and has a little give.
- Horsehide is usually firmer and smoother. Some sharpeners like it for very hard steel. Others find it less forgiving of small angle changes.
- Buffalo and other dense leathers are used on several premium bench strops, valued for their firmness.
- Suede or rough-side leather holds compound well but has more nap, which can round an edge if you press too hard.
Thinner leather glued firmly to a flat base flexes less than thick leather, which helps protect a thin edge.
Bare leather or compound?
Bare leather is enough to clean up a burr after a 3000–6000 grit stone. It’s the gentlest option.
Compounds add a fine abrasive and make the strop do more work:
- Green chromium oxide is a very fine, widely available bar compound. It works on most kitchen steels, though harder steels respond more slowly.
- Diamond sprays or pastes (often in the 0.5–3 micron range) cut very hard and high-alloy steels well and are popular with Japanese knife owners.
- CBN (cubic boron nitride) sprays behave similarly to diamond and are another option for hard steels.
Keep each compound on its own strop, or on its own side of a paddle. A strop loaded with a coarser compound will spoil the finish from a finer one.
Strops worth considering
Products change, so treat this as a starting list rather than a ranking. All of these are leather strops on a rigid base, which suits Japanese knives.
- Naniwa leather strop. Natural leather on a wooden base with a non-slip bottom. A straightforward bench strop from a well-known Japanese stone maker.
- Tojiro leather strop. A wide cowhide strop on a wood base from a Japanese knife maker. Usable bare or with a fine diamond or CBN spray.
- Suehiro leather strop and polishing kit. A compact strop sold with fine polishing compounds, convenient if you want everything in one box.
- Burrfection leather strop on hinoki. Dense leather on a hinoki wood base, aimed at people who strop often and want a firm surface.
- Cangshan two-sided paddle strop. An affordable paddle: compound on one side, bare leather on the other.
- BeaverCraft paddle strops. Inexpensive paddle strops, often sold with green compound. Fine for smaller knives and learning.
- Combination kits with a bamboo base. Several brands sell strops alongside whetstones. Quality varies, but these can be a reasonable starting point.
If you already have whetstones and want to keep costs down, a smooth leather offcut glued to a flat piece of hardwood makes a perfectly usable bench strop.
How to strop a Japanese knife
- Finish on the stone first. A strop polishes. It doesn’t sharpen a dull knife. Sharpen and deburr on your stones until the edge is close to finished. Our step-by-step whetstone guide covers this.
- Set the strop on a stable surface. Hold a paddle strop flat against the counter rather than in the air.
- Match your sharpening angle, or go very slightly lower. Lay the bevel flat on the leather, then pull. Raising the spine higher than the sharpening angle is the most common way to round the edge.
- Pull spine-first. The edge always trails. Never push the edge into the leather, or it will cut the strop.
- Use very light pressure. Roughly the weight of the knife plus a little guidance is enough. Pressing harder makes the leather bulge up around the edge.
- Alternate sides. Start with about 5–10 strokes per side, then reduce to single alternating strokes. Cover the whole edge, from heel to tip, on each pass.
- Check the edge. It should feel even along its length and slice paper cleanly. If a burr is still present, our guide to raising, feeling and removing a burr can help.
Single-bevel knives
For single-bevel knives such as a yanagiba or deba, strop mainly on the bevel side, keeping the wide bevel flat on the leather. Finish with one or two very light strokes with the flat back (ura) held flat against the strop, just to clear any burr. Don’t lift the back side off the leather, or you’ll create a bevel there.
Mistakes that round the edge
- Too much pressure, especially on soft leather
- Angle too high, or lifting the spine at the end of each stroke
- Too many strokes. Dozens of passes rarely help and can gradually dull a thin edge.
- Using a hanging strop without keeping it fully taut
- Grit contamination from a stone or a coarser compound left on the leather
Caring for a strop
Keep the strop covered or stored face-down to keep out dust and kitchen grease. Wipe or brush off metal debris occasionally. Recharge compound sparingly. A thin, even layer works better than a thick crust. Don’t wet leather strops unless the maker says it’s fine.
Common questions
Can you sharpen a Japanese knife at home?
Yes. Whetstones are the traditional and most flexible way to sharpen Japanese knives. Start with a 1000-grit stone and add a 4000–6000 finishing stone. Our guide to whetstones and grit suggests setups. Guided systems that go down to 15° or lower also work. Be cautious with pull-through sharpeners: most are set for wider Western angles. Our article on whether pull-through sharpeners are bad for your knives explains why.
Do you need a strop at all?
No. Careful deburring on a fine stone can leave an excellent edge without one. A strop simply makes the last step easier and more consistent, and it’s handy for quick touch-ups between sharpenings.
How often should you strop?
After each sharpening, and then for touch-ups whenever the knife starts to feel slightly less keen. For a home cook, that might be anywhere from every few days to every couple of weeks. Once stropping no longer brings the edge back, it’s time to go back to the stones.