Quick reference: factory angles by brand
All angles are per side. Makers change specs over time and some lines differ, so check the care information for your knife if you have it.
| Brand | Typical factory angle (per side) | Notes |
|---|---|---|
| Zwilling (Zwilling J.A. Henckels) | about 15° | Most Western-style lines; Japanese-style lines differ |
| Henckels (value brand) | about 15° on many current lines | Older or entry-level knives may sit wider, closer to 18–20° |
| Miyabi | about 9.5–12° | Japanese-made, hard steel; far lower than Western knives |
| Cutco | 15° on straight edges | Double-D serrated edges: send to Cutco rather than sharpening at home |
| Buck | about 13–16° | Many owners maintain a slightly wider edge or micro-bevel |
| Misen | about 15° | Misen markets its kitchen knives with a 15° edge |
If you’re new to the per-side vs total angle distinction, or want the trade-offs between angles explained, start with our guide to 15 vs 20 degree sharpening angles.
Zwilling and Henckels
Zwilling J.A. Henckels is a German company that sells knives under two main names: Zwilling (its premium German-made lines) and Henckels (its value-oriented lines, previously sold as Henckels International). Zwilling’s published guidance for its Western-style knives is about 15° per side.
Are Henckels knives 15 or 20 degrees?
Most current Zwilling and many current Henckels knives are around 15° per side. Older German knives, including older Henckels blades, were commonly sharpened wider, nearer 20°, and some entry-level knives still feel thicker at the edge. If you have an older or unlabelled Henckels knife, do the marker test described in our angle guide before deciding. If the bevel is wider than 15°, you can either keep it or reprofile it down over a few sessions.
Zwilling’s Japanese-style knives, including some santokus and the Miyabi range below, are sharpened at lower angles than its Western lines.
Zwilling vs Henckels lines
The general split is that Zwilling-branded lines (such as Pro, Four Star and Twin Signature) are the higher-end German-made knives, and Henckels-branded lines (such as Classic, Statement and Solution) are the more affordable ranges, often made outside Germany. Line names and manufacturing locations change, so check the current listing for your specific knife. For sharpening, the practical difference is mainly steel and edge thickness. Softer, thicker entry-level knives may hold up better at 17–20° than at 15°.
How to sharpen them: a 1000-grit whetstone, followed by a finer stone if you like a more polished edge, works well. Zwilling and Henckels also sell pull-through sharpeners with Western and Asian slots. These are convenient but remove more steel than a stone does. Our article on whether pull-through sharpeners are bad for your knives explains the trade-offs.
Miyabi
Miyabi is Zwilling’s Japanese brand, made in Seki, Japan. Miyabi knives use hard steels, and some lines use powdered steels, with edges sharpened at roughly 9.5–12° per side. That’s much lower than any Western knife on this page.
Miyabi knives are positioned as a premium line, and they need a gentler approach:
- Use whetstones or a guided system that goes below 15°. Most pull-through sharpeners can’t match a 10–12° edge and will widen it.
- Keep pressure light, especially on the edge-leading stroke, because thin, hard edges can chip.
- Go finer on grit. A 1000-grit stone to sharpen and a 3000–6000 stone to refine suits these steels. Our guide to whetstones and grit covers progressions.
- Strop lightly or use a ceramic rod between sharpenings rather than a grooved steel honing rod. See strops for Japanese knives.
Professional sharpening for Japanese knives is widely available, and prices vary by region and by whether the shop charges per knife or per inch. Ask whether they use whetstones or a belt grinder, and whether they’ll match the factory angle.
Cutco
Cutco says its straight-edge knives are sharpened at 15° per side (30° inclusive). Cutco sells a home sharpener set to that angle for its straight edges.
The important exception is Cutco’s Double-D serrated edge. Cutco advises against sharpening Double-D blades in a straight-edge sharpener or on a flat stone, and recommends returning them to the company instead. Cutco has long offered factory sharpening under its guarantee. Check its current terms and any shipping or handling fees before you send knives.
For straight-edge Cutco knives at home:
- Match 15° per side on a whetstone or guided system.
- A 1000-grit stone is usually enough. Some owners stop around 600–1000 grit for a slightly toothier edge on these knives.
- A few owners prefer a slightly wider angle, around 17°, for more durability. That’s a reasonable choice for a knife that gets heavy use.
Buck
Buck Knives says its blades are generally ground at about 13–16° per side from the factory, varying by model and intended use. That’s thinner than many people expect from a sturdy folding or hunting knife.
Two common approaches:
- Keep the factory angle. It slices well and suits skinning and general cutting, but it takes more care to maintain and can roll on hard work.
- Add a slightly wider edge or micro-bevel. Many owners sharpen at around 18–22° per side for a more durable edge that’s quicker to touch up. Buck’s own sharpening tutorials have shown wider angles being used.
If you’re new to sharpening a Buck knife, start at the factory angle with the marker test to confirm it. Then decide whether you want to widen it. Widening is quick. Going back down to the original angle later takes much more work.
Misen
Misen markets its kitchen knives with a 15° per side edge. Misen doesn’t sell its own home sharpener. Instead it has offered a mail-in sharpening service for knives of any brand. Misen’s sharpening terms have changed over time, including a move away from free lifetime sharpening, so check the current details on Misen’s site.
To sharpen a Misen knife at home:
- Use a whetstone at about 15° per side. A 1000-grit stone handles routine sharpening. A coarser stone (around 220–400) is only needed for chips or a very dull edge.
- Rolling sharpeners with a magnetic angle holder, or guided systems with a 15° setting, are easier alternatives if freehand sharpening isn’t for you.
- Finish by removing the burr and, if you like, a few strokes on a strop.
Our step-by-step whetstone guide works for any of these brands.
Should you always match the factory angle?
Matching the factory angle is the easiest and safest default. It removes the least steel and keeps the knife behaving the way the maker designed it. Good reasons to change it:
- The edge keeps rolling or chipping in your use. A slightly wider angle or micro-bevel may last longer.
- You want more slicing performance from a sturdy Western knife and don’t mind the work of reprofiling it lower.
- The edge has already been changed by years of pull-through sharpening, and you’d rather establish a clean, consistent bevel than chase the original.
If your brand or line isn’t listed
- Look for a care guide or FAQ on the maker’s website. Many publish a recommended angle.
- Use the marker test to find what’s on the blade now.
- If you still aren’t sure, use about 15° per side for Japanese-made and thin, hard knives and about 20° per side for thick, soft or inexpensive Western knives and pocket knives.
For a full chart by knife type, see what angle kitchen knives should be sharpened at.
Common questions
Are German knives 15 or 20 degrees?
Traditionally German knives were sharpened at around 20° per side. Several major German makers have since moved to thinner edges, around 14–15° per side, on their current lines. Older German knives and many budget ones are still closer to 20°.
Is 60 HRC brittle?
Not by itself. 60 HRC (Rockwell hardness) is common in Japanese kitchen knives and is harder than most German knives, which are often in the mid to high 50s. Harder steel holds a thin edge longer but is generally less tolerant of twisting, bone and impacts, so it’s more likely to chip than to roll. Heat treatment and the specific steel matter as much as the number.
What angle is best for a hunting knife?
Many hunting knives are sharpened around 20–25° per side for durability, especially if they’ll meet bone or joints. Knives used mainly for skinning or slicing can run lower, around 15–20°. Buck’s thinner factory edge is one example of a maker choosing a lower angle for slicing performance.